Yesterday morning, Ms. Pan reported to the reporter that on the evening of January 31st at around 6pm, a small restaurant owner near Guangping Street in Shahekou District was injured by five men and the contents of the hotel were beaten.
Our reporter Jiafeng
'They didn't say a few words, and they just punched and kicked me. At around 6pm on January 31st, Mr. Rong, the owner of a small hotel near Guangping Street in Shahekou District, was injured by five men and was admitted to the hospital. Items in the hotel were beaten. Rong's right eyebrow fracture and fundus hemorrhage. At present, he has alarmed.
Mr. Rong told reporters that he was greeting customers in the hotel that evening. Suddenly came a car outside the door and four young men stormed into the hotel after getting out of the car. After negotiating with him, he punched and kicked him. 'I don't know why they beat me or know them. Mr. Wing said that the beating process lasted for nearly ten minutes, during which a man also ran to the kitchen and took out the kitchen knife. The cook was scared to drop his livelihood and ran out. Afterwards, the four men took Mr. Rong from the house and continued to beat him outside the house. "They took me out of the house, got another man out of the car and took my brick with my back. 'Mr. Rong was knocked down again by the bricks, and he felt sensible and dizzy. Subsequently, five men left the scene by car. The entire murder process was recorded by the camera installed by Mr. Wing.
Yesterday morning, the reporter came to the hotel. Mr. Rong’s wife called the reporter a surveillance video. The picture shows that among the four men who advanced the door, a man in a vest rushed up to give Mr. Sung two slaps, and the other three behind him immediately started to beat Mr. Wing. "He cuts me off with a knife. Fortunately, I run fast, or I might be chopped. 'The hotel chef said. These men also broke the contents of the hotel. At that time, people did not know what had happened. After a while, they remembered the alarm.
Mr. Rong’s wife told reporters that they had only been operating the hotel here for more than a year. The time was short and did not enemies with anyone. As for why the husband was beaten, their husband and wife were puzzled. 'When I arrived, my husband squatted on the ground and the contents of the hotel were in a mess. The guests had scared away. 'Mr. Rong was subsequently taken to the hospital by his wife. After investigation, Mr. Rong had a fracture of his right eyebrow, bleeding in the fundus, multiple soft tissue injuries, and internal injuries. Further examination was needed.
At present, the civilian police in the area are investigating this matter.
Selective Laser Sintering (SLS) was developed at the University of Texas in Austin, by Carl Deckard and colleagues. The technology was patented in 1989 and was originally sold by DTM Corporation. DTM was acquired by 3D Systems in 2001. The basic concept of SLS is similar to that of SLA. It uses a moving laser beam to trace and selectively sinter powdered polymer and/or metal composite materials into successive cross-sections of a three-dimensional part. As in all rapid prototyping processes, the parts are built upon a platform that adjusts in height equal to the thickness of the layer being built. Additional powder is deposited on top of each solidified layer and sintered. This powder is rolled onto the platform from a bin before building the layer. The powder is maintained at an elevated temperature so that it fuses easily upon exposure to the laser. Unlike SLA, special support structures are not required because the excess powder in each layer acts as a support to the part being built. With the metal composite material, the SLS process solidifies a polymer binder material around steel powder (100 micron diameter) one slice at a time, forming the part. The part is then placed in a furnace, at temperatures in excess of 900 °C, where the polymer binder is burned off and the part is infiltrated with bronze to improve its density. The burn-off and infiltration procedures typically take about one day, after which secondary machining and finishing is performed. Recent improvements in accuracy and resolution, and reduction in stair-stepping, have minimized the need for secondary machining and finishing.
The main material for the SLS are the metal part or Nylon material which are commonly used in the industry or consumer fields. contact us to do the business, we are your best partner from beginning to end to give you the best service.
Selective Laser Sintering,Laser Sintering,Selective Laser Sintering 3D Printing,Laser Sintering Service
Suzhou FCE precision electronics Co., LTD , https://www.sjfukeyifcesz.com