On January 8, Anhui Quality Supervision Bureau announced the results of spotlights and lamps that were organized by the bureau in the province. Four of the samples were unqualified. A total of 19 samples were taken from 6 areas in Anhui Province, including 11 in Hefei, 2 in Huangshan, 2 in Lu'an, 2 in Wuhu, 1 in Tongling, and 1 in Zhangzhou. Samples were taken from the manufacturer. The test results were as follows: 15 groups were qualified, the total pass rate was 79%, and the unqualified group was 4, and the failure rate was 21%. The inspection basis for this spot check is the “Detailed Rules for Provincial Supervision and Inspection of Lamps and Lamps”. The main problems found in this spot check are as follows: 1. Mark. In the two groups of self-ballasted fluorescent lamps for general lighting, one group has a flag item that is unqualified. The main problem is that the manufacturer does not provide supplementary information on the lamp, or on the package, or in the instruction manual. Current. 2. Lamp power. In the two sets of self-ballasted fluorescent lamps for general illumination, one group has a lamp power project that is unqualified. The main problem is that the actual power consumed by the lamp exceeds the deviation range of the rated power. 3. Initial light effect / luminous flux. The two groups of ordinary lighting self-ballasted fluorescent lamps used in this spot check have unqualified initial light effects or luminous flux items. The main problem is that the manufacturer claims to be equivalent to a certain specification of incandescent lamps, but its luminous flux does not meet the GB/T17623-2013 standard. The value, or efficacy, does not meet the requirements of the GB/T17623-2013 standard. 4. Harmonic current. In the two groups of self-ballasted fluorescent lamps for general lighting, one group had a harmonic project that failed. The main problem was that the harmonic limits of the lamps did not meet the requirements of GB17625.1-2012. 5. Structure. One of the 17 sets of other luminaire samples in this spot check was unqualified. The main problem was that the power supply terminals were not positioned or protected. When the lamp is installed and used, there are safety hazards such as short circuit and electric shock. 6, internal wiring. Two of the 17 sets of other luminaire samples in this sample were found to have internal wiring failure. The main problem was that the end of the soft stranded wire was too tin-plated, and there was no measure to ensure that the clamped joint was not loose when the solder was cold-deformed. During the use of the luminaire, there are hidden dangers such as open circuit and poor contact. Purchase reminder: Anhui Quality Supervision Bureau reminds consumers to pay attention to the following points when purchasing products: Buy famous brand products produced by well-known enterprises, the products of well-known enterprises have good quality and reliable maintenance service guarantee. Check the product identification. The product specifications, models and trademarks should be consistent with the instructions. The product manual or nameplate should have the national compulsory certification mark (namely CCC mark), the name of the manufacturer, the product inspection certificate, and the execution standard code. If you need to buy a suitable product, you should not simply pursue low prices and avoid entering the low price trap. Because in general, products that deviate too much from normal prices objectively cannot guarantee product quality. On January 8, Anhui Quality Supervision Bureau announced the results of spotlights and lamps that were organized by the bureau in the province. Four of the samples were unqualified. A total of 19 samples were taken from 6 areas in Anhui Province, including 11 in Hefei, 2 in Huangshan, 2 in Lu'an, 2 in Wuhu, 1 in Tongling, and 1 in Zhangzhou. Samples were taken from the manufacturer. The test results were as follows: 15 groups were qualified, the total pass rate was 79%, and the unqualified group was 4, and the failure rate was 21%.

REAR Fenders For HONDA:

Yangzhou Gemini Vehicle Industry Co., Ltd. has more than 20 years experiences in producing and selling metal body parts of various vehicles. We are specialized manufacturer of REAR Fenders used for HONDA, including CITY, CIVIC, ACCORD, FIT, CRIDER, JADE, CROSSTOUR, VEZEL-HRV, X-RV, CRV, ODYSSEY, and SPIROIR. We own Hydraulic Machines, Punching Machines, Numerical Control cutting Machines, CNC Grinding Machines, Painting and Electrophoresis Coating lines. We provide "Professional Efficient Effective" service to all of our domestic and oversea customers. We are very glad to be contacted by you and hope that we can keep a long-term cooperation on the business of Steel Body Autoparts.

REAR Fenders For HONDA

REAR Fenders For HONDA,Honda Bobber Rear Fender,Honda Shadow Fenders,Honda Red Rear Fenders

Yangzhou Gemini Vehicle Industrial Co., Ltd , https://www.yzqsap.com